Enter and Exit DFU Mode on iPhone 7

How to Enter and Exit DFU Mode on iPhone 7 or iPhone 7 Plus

DFU mode permits all devices to recover from any state. DFU mode means device firmware upgrade mode where BootRom can receive IBSS. Basically, BootRom is one kind of Read-Only Memory, where stored a piece of code.

DFU is a part of the secure room that burns hardware, so it cannot be detached. In this post, I will share with you how to enter and exit DFU Mode on iPhone 7 or iPhone 7 Plus.

If you failed else you should give restore your iPhone. It is not restored generally; you should put it into DFU mode on your iPhone 7 or iPhone 7 plus. If you don’t know how to do DFU mode iPhone 7 or iPhone 7 Plus just follow our instructions here:

  1. If you haven’t previously done so, now Turn Off your iPhone.
  2. Plugin your iPhone 7 with your Mac or computer.
  3. Primarily, make sure iTunes is running on your Mac.
  4. Now, hold down the on/off button from the right side for 3 seconds of your device.
  5. Hold the volume down button and on/off button from the left side of your device.
  6. After that, press holding buttons (both) together for 10 seconds of your device. (If you realize the Apple logo, you’ve held them too long and you will essential to start again your device.)
  7. Run the on/off button but hold down the volume down button for 5 seconds. (If you see the “iTunes Plugin” screen, then you have to restart again.
  8. If notice that, your device screen is black, that’s it!
  9. Finally, your iPhone 7 device has been successfully in DFU mode.

Check Other Post: How To Upgrade Windows 7 To Windows 10.

What is DFU Mode?

DFU mode is a device firewire mode and is primarily used to downgrade your iOS but can also be used to install custom firmware to jailbreak the phone. It is a different recovery because iPhone 7 recovery mode is going to give you the latest version of iOS.

How to Use DFU Mode With the iPhone?

Now I’m going to share with you how to get your iOS device model. First of all, plug in your PC or Mac iTunes just launch automatically but it doesn’t read and launch it now. Then you’re going to want to turn off your phone to get into DFU mode. You have to press the power button and the home button but the process is a little different from the iPhone 7 because the home button is solid-state.

So first I am going to lead you through the process with iPhone 6s and 6s plus older and then I’ll go in how to it on the iPhone 7 first hold your iPhone power button for three seconds then put your other figure on the home button and hold them both down for 10 seconds.

Read More: How to Free Download and Install Zviewer Alternative for PC.

How to Enter and Exit DFU Mode on iPhone 7 or iPhone 7 Plus?

Let go of the power button and keep your finger on the home button for an additional five seconds. If you see the Apple logo or Plug into iTunes bad news and you did it wrong then, you can start the process over. If your screen is black then it is well.

You’re in DFU mode and now you should be able to spec your home. If you’re ready to make successfully DFU (device firmware upgrade) then press the Home button for 10 seconds or at the same time until the Apple logo appears.

.If you want to put your iPhone 7 in DFU mode the process is similar but you’re going to need your power button and the bottom volume button. So, I’ll say you that process now press the power button for 3 seconds then press the low volume button and hold them both for 10 seconds then let go of the power button and hold the lower volume button for five additional seconds.

Just I should be able to detect you’re ok. So, when you want to get out of DFU mode go and hold the power button and the lower volume button for 10 seconds or until the Apple logo shows up on your phone.

Don’t Miss: How to Clean Your Computer With Run Commands For Better Speed.

How to Put An iPhone In DFU Mode

The first thing you need to do is to plug in your iPhone to a computer. You can’t put your iPhone into DFU mode unless it’s plugged into iTunes. So, Plugging it in plug it into this Mac now. I’ve never hooked up this iPhone and synced it with this iTunes library before and that’s okay.

We just using the Mac right now as a tool to restore the iPhone. So, let’s say you’re having a problem with your computer. So, iTunes is now open on this Mac and I’m going to put this into DFU mode the good thing about it. DFU mode is that you can basically put an iPhone into DFU mode and ignore everything.

So how do you put an iPhone into DFU mode? After that, Hold the power button and the volume button together. Then let go of the power button and keep holding the volume down button. Similarly, the iPhone 6s below the first five seconds hold the power button and the home button.

Read Also: Chrome Remote Desktop For PC Free Download.

How to Put iPhone 7 & 7s in Recovery / Restore Mode

How to put your iPhone 7 and 7 Plus iPhone in recovery mode sometimes used to restore your device to a custom form via or if you are error when you’re restoring your device in normal mode putting your device in recovery mode and then restoring your device will get rid of that error.

So put your device in your curb remove first of all you have to turn off your device completely. your device is correctly turned off, press the Home button and connect your device to the computer via USB cable until you press the Home button. You will see the iTunes logo on your device screen.

Keep pressing the home button and iTunes will pop up letting you know your devices are in recovery mode. Now you can click on the restore and press the option key on the keyboard at the same time to browse bloom via and you saw your device to bloom via and you saw your device to that firmware. Now complete your work restore mode. If you like this article you can also read  How to  Successfully Connect Mac To Apple TV- Easy Way.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top